Tornado

Earth & Home

★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. Through interactive operation, the devices within the exhibit platform work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are equipment such as a water mist generator and a water level monitor. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

Options

• 0.9*0.9*1.9m 0.9*0.9*1.9m
  Dimensions (unit: m): 0.9*0.9*1.9m Brand: KexMall Model: PopsciCat-Ecological-012 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelaisi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel tube *4 ⑥ Wind gathering cover: Φ400mm acrylic cylinder 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjing® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: Powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. Through interactive operation, the devices within the exhibit platform work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are equipment such as a water mist generator and a water level monitor. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.0*2.1m Φ1.0*2.1m
  Dimensions (unit: m): Φ1.0*2.1m Brand: KexMall Model: PopsciCat-Ecological-013 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Columns: Φ63mm stainless steel tube *4 ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specifically for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Place directly ③ Entry passage: Door frame size (width × height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.0*2.2m · Style 1 Φ1.0*2.2m
  Dimensions (unit: m): Φ1.0*2.2m Brand: KexMall Model: PopsciCat-Ecological-014 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelaisi artificial stone, thickness ≧12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specifically for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Place directly ③ Entry passage: Door frame size (width × height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.2*2.3m Φ1.2*2.3m
  Dimensions (unit: m): Φ1.2*2.3m Brand: KexMall Model: PopsciCat-Ecological-015 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjing® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Place directly ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval of passage ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display stand, etc. When the visitor presses the start button, the exhibit demonstration starts, and the visitor can see the mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. ★Scientific Principle: When the visitor presses the start button, the exhibit demonstration starts, and the visitor can see the mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and as side air vents. During participation, the visitor presses the start button; when the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitor.

• Φ1.1*2.3m · Style 1 Φ1.1*2.3m
  Dimensions (unit: m): Φ1.1*2.3m Brand: KexMall Model: PopsciCat-Ecological-016 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electric control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• Φ1.0*2.2m · Style 2 Φ1.0*2.2m
  Dimensions (unit: m): Φ1.0*2.2m Brand: KexMall Model: PopsciCat-Ecological-017 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel tube *6 ⑥ Wind gathering cover: Φ400mm acrylic cylinder 2. Main Configuration: ① Electric control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• Φ1.1*2.3m · Style 2 Φ1.1*2.3m
  Dimensions (unit: m): Φ1.1*2.3m Brand: PopsciCat Model: PopsciCat-Ecological-018 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjing® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 2 sets ⑥ Water pump: Submersible pump 135W 3000L ⑦ Exhaust fan: 16-inch circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame dimensions (width × height) ≥1.5m×2.0m, continuous turning interval of passage ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit platform work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air vents. During participation, visitors press the start button. Once the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.2*2.4m · Style 1 Φ1.2*2.4m
  Dimensions (unit: m): Φ1.2*2.4m Brand: KexMall Model: PopsciCat-Ecological-019 1. Materials: ① Exhibit stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ90mm seamless pipe *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display stand, etc. When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• Φ1.2*2.4m · Style 2 Φ1.2*2.4m
  Dimensions (unit: m): Φ1.2*2.4m Brand: KexMall Model: PopsciCat-Ecological-020 1. Materials: ① Exhibit stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ63mm stainless steel pipe *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display stand, etc. When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• Φ1.3*2.5m · Style 1 Φ1.3*2.5m
  Dimensions (unit: m): Φ1.3*2.5m Brand: PopsciCat Model: PopsciCat-Ecological-021 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100 seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large-capacity submersible pump ⑦ Exhaust fan: Circular powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air vents. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.3*2.5m · Style 2 Φ1.3*2.5m
  Dimensions (unit: m): Φ1.3*2.5m Brand: KexMall Model: PopsciCat-Ecological-022 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube *3 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-reset 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Power frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado that visitors see.

• Φ1.3*2.5m · Style 3 Φ1.3*2.5m
  Dimensions (unit: m): Φ1.3*2.5m Brand: KexMall Model: PopsciCat-Ecological-023 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube *3 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-reset 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Power frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado that visitors see.

• Φ1.4*2.5m · Style 1 Φ1.4*2.5m
  Dimensions (unit: m): Φ1.4*2.5m Brand: KexMall Model: PopsciCat-Ecological-024 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame dimensions (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. When visitors press the start button to activate the demonstration, they can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air vents. During participation, visitors press the start button. Once the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the tornado-like simulation seen by visitors.

• Φ1.4*2.6m · Style 1 Φ1.4*2.6m
  Dimensions (unit: m): Φ1.4*2.6m Brand: KexMall Model: PopsciCat-Ecological-025 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electric control: Electrical logic control system, equipped with Guanjian® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.4*2.5m · Style 2 Φ1.4*2.5m
  Dimensions (unit: m): Φ1.4*2.5m Brand: KexMall Model: PopsciCat-Ecological-026 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube *3 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electric control: Electrical logic control system, equipped with Guanjian® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration. They can see the water mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.4*2.5m · Style 3 Φ1.4*2.5m
  Dimensions (unit: m): Φ1.4*2.5m Brand: KexMall Model: PopsciCat-Ecological-027 1. Materials: ① Display stand frame: 25 square tube, 2.0mm cold-rolled steel panel ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled steel panel ⑤ Columns: Φ100mm stainless steel tube *3 ⑥ Wind gathering cover: 8mm acrylic panel 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjin® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large-capacity submersible pump ⑦ Exhaust fan: Circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation base: Place directly ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, an exhaust fan, a display frame, etc. Visitors press the start button to activate the exhibit demonstration. They can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the exhibit demonstration. They can see the mist form a funnel shape under the action of the exhaust fan, just like the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. Through interactive operation, the devices within the exhibit platform work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as supports and side air inlets. During participation, visitors press the start button. Once the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado that visitors see.

• 1.5*1.4*2.5m 1.5*1.4*2.5m
  Dimensions (unit: m): 1.5*1.4*2.5m Brand: KexMall Model: PopsciCat-Ecological-028 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Wind gathering cover: 8mm acrylic enclosure ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube*4 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Inertia® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Exhibition Requirements: ① Energy requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width×height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance passage: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• 1.6*1.3*2.6m 1.6*1.3*2.6m
  Dimensions (unit: m): 1.6*1.3*2.6m Brand: KexMall Model: PopsciCat-Ecological-029 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelaisi artificial stone, thickness ≧12mm, with flame-retardant board underneath ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube*3 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Inertia® K3 type high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful exhaust fan 3. Exhibition Requirements: ① Energy requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width×height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance passage: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. When the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• 1.7*1.4*2.5m 1.7*1.4*2.5m
  Dimensions (unit: m): 1.7*1.4*2.5m Brand: PopsciCat Model: PopsciCat-Ecological-030 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Wind gathering cover: 8mm acrylic enclosure ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm seamless tube *4 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Inertia® K3 high-power PLC controller with protection specifically for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular exhaust powerful fan ⑧ Video system: 17-inch HD display + video player 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button to observe the generation of a tornado; watch the tornado explanation video. ★Exhibit Description: The exhibit consists of a smoke generator, exhaust fan, display stand, etc. Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the water mist forming a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. The exhibit reproduces the state of a tornado through physical simulation. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are water mist generators, water level monitors, and other equipment. Several columns of the exhibit serve both as support and side air vents. During participation, visitors press the start button; when the exhibit is activated, the water mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• Φ1.4*2.6m · Style 2 Φ1.4*2.6m
  Dimensions (unit: m): Φ1.4*2.6m Brand: KexMall Model: PopsciCat-Ecological-031 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: Kelesi artificial stone, thickness ≥12mm, with flame-retardant board underneath ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer: 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular strong exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button and observe the formation of the tornado. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display frame, etc. When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. Once the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• 1.6*1.2*2.5m 1.6*1.2*2.5m
  Dimensions (unit: m): 1.6*1.2*2.5m Brand: KexMall Model: PopsciCat-Ecological-032 1. Materials: ① Display stand frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: 3mm anti-slip chequered plate ③ Description plate, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guanjian® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer: 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular strong exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame size (width × height) ≥1.5m×2.0m, continuous turning interval ≥3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button to observe the formation of the tornado; step into the tornado to feel the power of the wind. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display frame, etc. When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column of a tornado. The exhibit uses physical simulation to reproduce the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. On the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button. Once the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

• Φ1.5*2.5m Φ1.5*2.5m
  Dimensions (unit: m): Φ1.5*2.5m Brand: KexMall Model: PopsciCat-Ecological-033 1. Materials: ① Platform frame: 25 square tube, enclosure 2.0mm cold-rolled sheet ② Tabletop: 3mm anti-slip diamond plate ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled sheet ⑤ Columns: Φ100mm stainless steel tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Inertia® K3 high-power PLC controller with protection specially for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer 4 sets ⑥ Water pump: Large capacity submersible pump ⑦ Exhaust fan: Circular powerful exhaust fan 3. Exhibition Requirements: ① Power requirement: AC100-240V, 50/60Hz500W (standard three-wire socket) ② Installation foundation: Direct placement ③ Entry passage: Door frame size (width × height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical Interaction ★Operation: Press the "Start" button to observe the formation of the tornado; step into the tornado to feel the power of the wind. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display frame, etc. Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. ★Scientific Principle: Visitors press the start button to activate the demonstration, and they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. Through interactive operation, the devices within the platform work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are mist generators, water level monitors, and other equipment. The several columns of the exhibit serve both as support and side air vents. During participation, visitors press the start button; when the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by the visitors.

• 1.7*1.2*265m 1.7*1.2*265m
  Dimensions (unit: m): 1.7*1.2*265m Brand: KexMall Model: PopsciCat-Ecological-034 1. Materials: ① Display stand frame: 25 square tube, 2.0mm cold-rolled steel enclosure ② Tabletop: 3mm anti-slip chequered plate ③ Instruction sign, graphic panel: 5mm thick acrylic UV printing ④ Maintenance door: 2.0mm cold-rolled steel ⑤ Columns: Φ100mm seamless tube *4 ⑥ Wind gathering cover: 8mm acrylic enclosure 2. Main Configuration: ① Electrical control: Electrical logic control system, equipped with Guandu® K3 high-power PLC controller with protection specifically for science exhibits ② Button: Self-resetting 22mm stainless steel metal button with ring light; LED voltage not higher than 12V ③ Delay module: Input: AC100-240V, 50/60HzAC Output: AC or DC Delay time: 0-10 minutes ④ Blower: Industrial frequency centrifugal fan ⑤ Atomizer: 4 sets ⑥ Water pump: Large-capacity submersible pump ⑦ Exhaust fan: Circular powerful exhaust fan 3. Installation Requirements: ① Power requirement: AC100-240V, 50/60Hz 500W (standard three-wire socket) ② Installation base: Direct placement ③ Entry passage: Door frame dimensions (width × height) ≧1.5m×2.0m, continuous turning interval ≧3m ④ Maintenance access: Not required ⑤ If conditions permit, reserve water inlet and outlet

  ★Exhibit Content: Tornado ★Interaction: Electromechanical interaction ★Operation: Press the "Start" button to observe the formation of the tornado; step into the tornado to feel the power of the wind. ★Exhibit Description: The exhibit consists of a mist generator, exhaust fan, display frame, etc. When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. ★Scientific Principle: When visitors press the start button to activate the demonstration, they can see the mist form a funnel shape under the action of the exhaust fan, similar to the funnel-shaped cloud column produced by a tornado. Through physical simulation, the exhibit reproduces the state of a tornado. Through interactive operation, the devices within the exhibit work together to simulate the movement pattern of a tornado. At the bottom platform of the exhibit, there are a mist generator, water level monitor, and other equipment. Several columns of the exhibit serve both as support and side air inlets. During participation, visitors press the start button; when the exhibit is activated, the mist generator, tornado generator, etc., work simultaneously to create mist from the bottom of the device. Driven by the industrial fan and side air, the mist's trajectory gradually forms a rotating upward trend and is eventually drawn into the exhaust system. This cycle repeats, creating the on-site simulation of a tornado as seen by visitors.

Review

Principle Display: ★★★★ Interaction Effect: ★★★ Ease of Installation: ★★★★★ Durability: ★★★★ Overall Rating: ★★★★

Browse all exhibits